IBM 16/4 Token-Ring Low Profile PCI Management Adapter User's Guide

Software installation

This chapter describes how to install the driver software for your token-ring adapter. To install the software, perform the following procedures:

1. Get the latest level of LAN driver updates for your operating system to ensure that your code is at the latest level.
2. Make sure that your adapter has already been installed in your computer. If it has not, follow the instructions in Installing the adapter hardware.
3. Get the driver for your environment. There are three places to find the driver. We recommend the first one listed here. All three methods will place the driver in a directory according to the structure in Table 1.
   • Method A: Get the driver from a software package on the IBM Networking Web site. This will ensure that you get the latest driver.
     1. Go to x:\startcd.htm (where x is your CD-ROM drive).
     2. Select your adapter from the section IBM Networking Web site - current information.
     3. Select Downloads and select the appropriate software package for your environment.
     4. Run the package to expand the files. The driver will be placed in the directory listed in Table 1.

     Note:

     You can also access the Web site directly at http://www.ibm.com/networking/support.

   • Method B: Use the driver shipped on this CD-ROM directly with your network operating system's installation software. Note the directory containing the driver (see Table 1).
   • Method C: Get the driver from a software package shipped on this CD-ROM.
     1. Go to x:\startcd.htm (where x is your CD-ROM drive).
     2. Select your adapter from the section CD-ROM - release date information.
     3. Select Downloads and choose the appropriate software package for your environment.
     4. Execute the package to expand the files. The driver will be placed in the directory listed in Table 1.
4. Install the driver. Use Table 2 to find the location of the installation instructions for your environment. We recommend that you install the latest service pack for your operating environment before installing the adapter software.

Table 1. Driver file directory structure

Operating System	Directory
Windows NT(R) 4.0	\(root)
Windows(R) 98 Second Edition (SE)	\(root)
Windows Me	\(root)
Windows 2000	\(root)

Table 2. Installation instructions

Environment	Page
Windows NT 4.0	"Windows NT Version 4.0"
Windows 98 / Windows Me	"Windows 98 SE / Windows Me"
Windows 2000 Professional	"Windows 2000"
Remote Unattended Installation (Windows NT, Windows 98, Windows 2000)	"Remote unattended installation of Windows 98, Windows 2000, and Windows NT"
Novell Client for Windows NT	"Novell Client for Windows NT"
Novell Client for Windows 98	"Novell Client for Windows 95/98"
Managed Driver Upgrade (Windows NT, Windows 98, Windows Me, Windows 2000)	"Managed Driver Upgrade for Windows 98, Windows Me, Windows NT, and Windows 2000"

Windows NT Version 4.0

The following procedure assumes that Windows NT 4.0 has already been installed with networking support. It is highly recommended that you install the latest service pack from Microsoft before installing the driver.

1. Log on to Windows NT as an administrator.
2. Select Start > Settings > Control Panel.
3. From the Control Panel window, double-click the Network icon.
4. Select the Adapters tab.
5. Select Add.
6. You will see a dialog box that includes a list of adapters. Select Have Disk....
7. Insert the CD-ROM or the diskette containing the device drivers into the appropriate drive. When prompted, enter the path to the root directory of the CD-ROM or diskette and select OK.
8. In the Select OEM Option dialog box, select IBM Token-Ring PCI Family Adapter and then select OK.

   Several work-in-progress panels are displayed, indicating that the driver and its supporting files are being copied to your computer's hard disk.

9. The Network Control panel is displayed again. There should be an entry in the Installed Adapters list for each token-ring adapter found in the computer.

   To change default values for an adapter, select that adapter on the Network Adapters list, and then select Properties. Make the necessary changes and select OK.

   Note:

   Make sure that all of the appropriate protocols are installed to connect to the network. Consult your network administrator if you are unsure of what protocols need to be installed.

10. Select Close to complete the installation.

    Note:

    If TCP/IP is installed as a protocol on the computer, you will now see the TCP/IP configuration panel. Enter all necessary information and select OK.

11. The following message will be displayed:

    Your network settings have changed.
    You will need to exit and restart Windows NT so that the new
    settings can take effect.
    

    Select Yes in order to have Windows NT automatically restart your computer.

    Note:

    You might need to reinstall the Service Pack due to changes to your services or protocols during installation.

12. Check for the following conditions to determine whether the adapter is working correctly and whether installation has been completed successfully:
    • The device driver files loaded successfully.
    • There are no error messages logged for the IBMTRP service in the Event Viewer.
    • The adapter LEDs indicate normal operation: Green ON, Amber OFF.

If you experience problems, see Problem solving.

Windows 98 SE / Windows Me

Windows 98 ships with a device driver for your adapter. Although the driver will function with the adapter, it is strongly recommended that you use the driver included with your adapter. Windows Me does not have a device driver that works with your adapter. You need to install the Windows Me driver included with your adapter.

Use one of the following procedures to install the latest driver.

Installing the driver for a first-time Windows 98 or Windows Me installation

If you install Windows 98 or Windows Me on a computer that already has the adapter installed, Windows may install a default driver for the adapter. If so, use the following procedure to install the driver that came with your adapter.

1. Select Start > Settings > Control Panel. This will display the Control Panel.
2. Look for the System icon. If you have a Windows Me system and you cannot see the System icon, click View all Control Panel options to expand your view.
3. Double-click the System icon to load the System Properties dialog.
4. Select the Device Manager tab.
5. In the Device Manager, expand the Network adapters section by selecting the + that appears to the left of the words "Network adapters" or "Other devices". Select the entry labeled IBM PCI Token-Ring Adapter,NDIS4 or PCI Token-Ring Controller, and then select Properties.
6. Select Driver to display the the information on this page, and then select Update Driver.
7. At this point, the Update Device Driver Wizard dialog box opens. The dialog box contains the following text:

   This wizard searches for updated drivers for:
   IBM PCI Token-Ring Adapter,NDIS4 or PCI Token-Ring Controller.
   

   On Windows 98 systems, select Next to continue.

8. Select Search for the best driver for your device and then select Next.
9. The next page of the wizard will ask where you would like to look for the device driver.
   • If you are installing the device driver from the product CD-ROM, insert the CD-ROM into the CD-ROM drive and make sure that the CD-ROM drive checkbox is checked.
   • If you are installing from a diskette that you built from the CD-ROM or from the Web, insert the diskette and make sure that the Floppy disk drives checkbox is checked.
10. Select Next to continue. Windows should find an updated device driver on the diskette or the CD-ROM. Make sure that the updated driver is selected and select Next.
11. The next page of the wizard should confirm that the hardware and device driver are found. Select Next again to begin copying files.

    Windows might prompt you for the driver diskette. Type the letter of your drive.

    Windows might also prompt you for the Windows 98 or Windows Me CD-ROM in order to install its default network protocols. Make sure that the location of your Windows installation files (for example, d:\ or d:\win98 or d:\win9x or c:\windows\catroot) appears in the entry and select OK.

12. The wizard reports after the files have finished copying that:

    Windows has finished installing an updated driver for your hardware
    device.
    

    Select Finish to continue.

13. Windows returns you to the adapter properties page. Select Close to continue.
14. Next, you are returned to the Device Manager page. Select Close again to complete the process.
15. Reboot the computer to ensure that all components of the driver loaded correctly.
16. Check for the following conditions to determine whether the adapter is working correctly and whether installation has been completed successfully:
    • The device driver files loaded successfully.
    • The Device Manager (System control panel applet) reports that the device is working correctly.
    • The adapter LEDs indicate normal operation: Green ON, Amber OFF.

If you experience problems, see Problem solving.

Installing the driver when Windows 98 or Windows Me is already installed

Use this procedure to install the driver that came with your adapter in a computer that already has Windows 98 or Windows Me running. This procedure assumes you have already installed the adapter.

1. When Windows boots, it will detect the new hardware and display the Add New Hardware Wizard dialog. This dialog should contain the following text:

   This wizard searches for new drivers for:
   IBM PCI Token-Ring Adapter,NDIS4.
   

   On Windows 98 systems, select Next to continue.

2. Select Search for the best driver for your device and then select Next.
3. The next page of the wizard will ask where you would like to look for the device driver.
   • If you are installing the device driver from the product CD-ROM, insert the CD-ROM into the CD-ROM drive and make sure that the CD-ROM drive checkbox is checked.
   • If you are installing from a diskette that you built from the CD-ROM or from the Web, insert the diskette and make sure that the Floppy disk drives checkbox is checked.
4. Select Next to continue. Windows should find an updated device driver on the diskette or the CD-ROM. Make sure that The updated driver is selected and select Next.
5. The next page of the wizard should confirm that the hardware and device driver are found. Select Next again to begin copying files.

   Windows might prompt you for the driver diskette. Type the letter of your drive.

   Windows might also prompt you for the Windows 98 or Windows Me CD-ROM in order to install its default network protocols. Make sure that the location of your Windows installation files (for example, d:\ or d:\win98 or d:\win9x or c:\windows\catroot) appears in the entry and select OK.

6. The wizard reports after the files have finished copying that:

   Windows has finished installing the software that your new hardware
   device requires.
   

   Select Finish to continue.

7. A dialog box displays the following message:

   To finish setting up your new hardware, you must restart your
   computer. Do you want to restart your computer now?
   

   Remove the diskette or CD-ROM from your computer and select Yes.

8. Check for the following conditions to determine whether the adapter is working correctly and whether installation has been completed successfully:
   • The device driver files loaded successfully.
   • The Device Manager (System control panel applet) reports that the device is working correctly.
   • The adapter LEDs indicate normal operation: Green ON, Amber OFF.

If you experience problems, see Problem solving.

Windows 2000

Before installing the device driver, make sure that the adapter is installed in your computer.

Windows 2000 may automatically install a default device driver for your adapter. However, we recommend that you upgrade to the driver that we provide for the adapter. Use the following procedure to install the upgraded driver for Windows 2000.

1. Select My Network Places on the Windows desktop.
2. Select Network and Dial-up Connections to display the Network and Dial-up Connections window.
3. Scroll the left side of the window to locate and select Network Identification.
4. In the System Properties window, select the Hardware tab.
5. Select the Device Manager button.
6. In the Device Manager window, click the + next to Network adapters to expand the list of adapters.
7. Select your adapter and select the Properties button.
8. In the Properties window for your adapter, select the Configure button.
9. Select the Driver tab.
10. Select the Update driver... button to open the Update Device Driver Wizard.
11. Select Next to continue.
12. On the next page, select Search for the best driver for your device and then select Next.
13. The next page of the wizard will ask where you would like to look for the device driver.
    • If you are installing from a diskette, insert the diskette and make sure that the Floppy disk drives checkbox is checked.
    • If you are installing from a location on your hard drive, make sure that the Specify a location checkbox is checked.
14. Select Next to continue. Make sure that driver you want updated is displayed on on the screen and select Next.

    Note:

    If the wizard does not specify the correct driver location, for example the CD-ROM or diskette drive, perform the following steps: Click the Back button twice. Select Display a list of known drivers . . . and then select Next. Select Have Disk. . . and then specify the location of the driver (the CD-ROM or diskette drive letter). After you select the correct driver, an Update Driver Warning window might appear. If so, click Yes to continue.

15. The next page of the wizard should confirm that the hardware and device driver are found. Select Next again to begin copying files.

    Notes:

    1. Windows might prompt you for the driver diskette. If so, type the letter of your drive.

    2. Windows might also prompt you for the Windows 2000 CD-ROM in order to install its default network protocols. Make sure that the location of your Windows 2000 installation files (for example, d:\ or d:\win2000 or c:\windows\catroot) appears in the entry and select OK.

    3. A Digital Signature Not Found window might appear saying that the driver is not digitally signed. If so, select Yes to continue.

    After the files are copied, the wizard displays a message to inform you that the driver was installed.

16. Select Finish to continue.
17. Select Yes when asked to reboot the system.
18. Check for the following conditions to determine whether the adapter is working correctly and whether installation has been completed successfully:
    • The device driver files loaded successfully.
    • The Local Area Connection icon on the Network and Dial-up Connections window shows that the device is working correctly.
    • The adapter LEDs indicate normal operation: Green ON, Amber OFF.

Remote unattended installation of Windows 98, Windows 2000, and Windows NT

Instructions for this environment are on the adapter CD-ROM. You can read the instructions with a Web browser. To access the instructions, perform the following steps:

1. Go to x:\startcd.htm (where x is your CD-ROM drive).
2. Select the proper adapter and then select Downloads.
3. Select the proper operating system to expand the list of packages.
4. Select Remote Unattended Install (RUI).

Novell Client for Windows NT

1. If the NDIS driver is not already installed, follow the instructions in Windows NT Version 4.0. At step 11 of those instructions, make sure that you select the appropriate protocols and services to connect to the network.

   Note:

   If you are connecting to a Novell server through IPX, you need to install the NWLink IPX/SPX Compatible Transport protocol and also the Client Service for NetWare service under the Services > Workstation tab.

2. Download Novell Client for Windows NT from http://www.novell.com/download/
3. Unzip the downloaded file to a local directory.
4. Run I386\SETUPNW.EXE from the directory where you placed the files.
5. Select YES or NO to respond to the Novell License Agreement.
6. You might get a message indicating that the Microsoft Client Service for NetWare is installed and will be removed. If so, respond Continue.
7. Installation is complete when you see the Installation Complete panel.
8. Reboot and start Windows NT to connect and log in to your server.

Novell Client for Windows 95/98

Note:

You can download Novell Client for Windows 95/98 from http://www.novell.com/download/

If you are upgrading from the NetWare DOS Requester (VLM) client or if you do not have any network client installed, you need to have the Windows 98 CD-ROM or diskettes or the Windows 98 .CAB files.

1. If the NDIS driver is not already installed, follow the instructions in Windows 98 SE / Windows Me.
2. After downloading the code, run SETUP.EXE.
3. Select Yes or No to respond to the Novell License Agreement.
4. Select Start to begin the installation.

   If you are prompted to select a adapter, select one that matches your hardware (this step might not be necessary, as you should have already selected the adapter in the first step).

5. If you do not need to customize your installation, select Reboot.
6. If you want optional features or need to configure your workstation, select Customize. Then select Reboot.

Managed Driver Upgrade for Windows 98, Windows Me, Windows NT, and Windows 2000

Managed Driver Upgrade is a package you can download from the IBM Token-Ring PCI Family Adapter Web site that assists local users and system administrators in upgrading their systems to the latest level of the driver. The package consists of the new driver, all necessary support files, and an executable program that can upgrade the driver without any user intervention.

Managed Driver Upgrade can be run locally by the user, or remotely by a system administrator using management software such as Tivoli TME^(R) 10 Software Distribution.

Running Managed Driver Upgrade locally

To run the Managed Driver Upgrade locally, perform the following procedure.

1. Download the correct package for your operating system.
2. Run the package and extract all the files to a single directory such as c:\temp.
3. If you are using Windows NT 4.0, log in using a user ID with administrator privileges.
4. Open a DOS or command window.
5. Run the Managed Driver Upgrade executable. The name of the executable is TRMDU98.EXE for Windows 98 and Windows Me, TRMDU00.EXE for Windows 2000, and TRMDUNT.EXE for Windows NT 4.0.
6. Enter the following command line options as needed. Refer to the following table.
   

   Table 3. Managed Driver Upgrade command line options
   

   Option	Explanation
   /boot=[y,n]	The adapter needs to be rebooted before the upgrade takes effect. The Managed Driver Upgrade executable can force the system to reboot after it completes. Set /boot=y if you want the system to reboot. Set /boot=n if you do not want the system to reboot. The default is /boot=y.
   /down=[y,n]	There are times when you might want to revert to a previous version of a driver. Set /down=y in these cases. Set /down=n to prevent an older driver from being accidentally installed over a newer driver. The default is /down=n. Windows NT 4.0 does not support this option.
   /file=[y,n]	Controls the logging ability of the Managed Driver Upgrade executable. /file=y will generate a log file in the same directory where the executable resides. /file=n suppresses logging. The default is /file=y
   /name=[XXXXXXXX.XXX]	Customizes the name of the log file. The name can be any valid Windows filename. The default name is MYOUT.DAT.

   For example, to execute on Windows 98, log to a file called TRMDU.LOG, and reboot after completion, enter the following on the command line:

   TRMDU98 /boot=y /file=y /name=TRMDU.LOG
   

Running Managed Driver Upgrade remotely

To run the Managed Driver Upgrade from a remote location using management software, perform the following procedure.

1. Download the correct package for the operating system to the management server.
2. Run the package and extract all the files to a single directory.
3. Repackage the files according to the specifics of the management software.
4. Follow the directions included with the management software to schedule an update. During the update, all the files in the package are typically pushed to the client, and the executable is started. The command line options for the executable described in Table 3 can typically be passed to the executable by the management software.

The Managed Driver Upgrade should be completely transparent to the user. The log file generated by Managed Driver Update will be stored in a directory designated by the management software. Refer to the management software for details on how to locate this directory.